Bandsaw STILER G5027

The STILER G5027 band saw enables cutting in a plane perpendicular to the axis of the material being cut or at any angle ranging from -45 to +60 degrees.

The feed during cutting takes place by gravity on the principle of oil flow in a two-chamber hydraulic cylinder. The appropriate speed of the arm drop is set with the help of the regulator located on the control panel.

A cast iron workbench with a rotating arm and a control panel on a separate pedestal is attached to the base.

It can be used to set the speed of the cutting band as well as turn on / off the machine. We can choose between two speeds of the cutting band 36 and 72 m / min.

The machine is equipped with a roller that feeds the material to be cut and a bumper for the length of the cut material.

The vice is placed in an adjustable bed and is equipped with a quick clamp.

The base is built as a rigid body welded from steel sheets. Inside there is a separate coolant tank with an electropump and a large drain pan.

The design of the upper part of the base provides a basin for draining the coolant and catching the chips produced during the cutting of the material.

SPECIFICATION:

The arm of the cutter is made of a uniform cast iron with a 27 mm wide cutting band used in this cutter. enables the full performance of multi-series cuts of both profiles and full materials.
STILER G5027 allows you to cut a whole range of materials, from black steel, pipes, profiles, channels, ending with quality steel, stainless steel, acid steel and solid materials.
The belt guides are equipped with special carbide inserts and bearings. This has a huge impact on the belt guiding, its service life, straightness, accuracy and quality of the cut.
In the lower position of the arm (after cutting the material), the saw band drive and the cooling system are automatically turned off.
Safety will be ensured by the cutting band covers and micro-switches that stop the engine's operation after the end of the cutting cycle or opening any of the covers, additional protection consists in switching off the cutter automatically in the event of the cutting band breaking.
The engine is equipped with new generation thermal fuses.
The drive from the engine to the belt driving pulley is transferred by means of a maintenance-free worm gear.
Roller feeders - in an additional option - available at our other auctions.

The STILER G5027 band saw enables trimming in a plane perpendicular to the axis of the material being cut or at any angle ranging from -45 to +60 degrees.
The feed during cutting takes place by gravity on the principle of oil flow in a two-chamber hydraulic cylinder. The appropriate speed of the arm drop is set with the help of the regulator located on the control panel.
The arm of the cutter is made of a uniform cast iron with a 27 mm wide cutting band used in this cutter. enables the full performance of multi-series cuts of both profiles and full materials. The vice is placed in an adjustable bed and is equipped with a quick clamp.
STILER G5027 allows you to cut a whole range of materials, from black steel, pipes, profiles, channels, ending with quality steel, stainless steel, acid steel and solid materials.
The belt guides are equipped with special carbide inserts and bearings.
This has a huge impact on the belt guiding, its service life, straightness, accuracy and quality of the cut.
The set includes a roller for feeding the material to be cut and a bumper for the length of the cut material.
The speed of the cutting band is regulated on the cutting machine's control panel. We can choose between two speeds: 36 and 72 m / min.
In the lower position of the arm (after cutting the material), the saw band drive and the cooling system are automatically turned off.
Safety will be ensured by the cutting band covers and micro-switches that stop the engine's operation after the end of the cutting cycle or opening any of the covers, additional protection consists in switching off the cutter automatically in the event of the cutting band breaking.
The engine is equipped with new generation thermal fuses.
The base is built as a rigid body welded from steel sheets. Inside there is a separate coolant tank with an electropump and a large drain pan.
The design of the upper part of the base provides a basin for draining the coolant and catching the chips produced during the cutting of the material.
A cast iron workbench with a rotating arm and a control panel on a separate pedestal is attached to the base.
In the cutting process, the main cutting movement is to move the cutting band.
The drive from the engine to the belt driving pulley is transmitted by a worm gear.